Click Here

 

Are you currently on the lookout for information and facts concerning How to Install a Bathtub?

Mounting a bathtub isn't exactly rocket science, however it does call for strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably hard job. If the old bathtub is conveniently available, the project can relocate speedily; if you need to open a wall to eliminate the old bathtub and also place the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub and also embeded in the brand-new one. Ensure you have certified yourself for the job and fit attempting it. Rather than employing a specialist to take over a halfway-completed project, it is far better to take into consideration using one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This write-up will certainly help you mount a new bath tub in your bathroom if you have actually currently acquired a new tub as well as do not require to change the arrangement of your previous water supply pipes.
Your devices as well as material checklist need to make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome as a result of the restricted gain access to that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the staying water that will originate from the pipes. As soon as the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming during this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Before going on to fit the brand-new faucets, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will certainly require a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in location between the tap and also the sink. Safeguard the faucet in position with the maker given backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap ends first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Mounting the Bath tub

Utilizing the two wood boards under its feet, place the bathtub in the required position. The wooden boards are useful in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and also changing the feet on the tub till the level reviews degree.
To mount taps, fit all-time low of the outermost adaptable faucet port to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Switch on the water supply and also check all joints and also brand-new pipework for leakages and also tighten them if needed. Fill the tub as well as also check the overflow electrical outlet as well as the regular electrical outlet for leaks.
Ultimately, fix the bath paneling as described in the producer's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the bath tub has actually been made use of at least when as this will resolve it into its final setting.

 

 

Preparing for the Setup

To start with, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to see to it that if the tap features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last position.

 

 

Tiling Around the Bath tub

In the location where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to crack an inflexible seal, causing the water to penetrate the wall in between the bath as well as the tiling, causing difficulties with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and also installations. They are sold in tubes and cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can break rather early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly available on the marketplace. It is a good idea to fit the floor tiles using waterproof or water-proof sticky and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you liked our article on Tools You Need to Install a New Bathtub . Many thanks for taking a few minutes to read our blog. Remember to set aside a second to promote this entry if you enjoyed reading it. Thanks so much for taking the time to read it.

Access top-rated emergency plumbers.